Feed Pipes, Inlet Devices & Impingement Baffles

Feed entering a column carries momentum. Dropped straight onto a packed bed it erodes packing, breaks up liquid into fine droplets that the bed cannot handle, and can set up vibration in the internals. A feed pipe and baffle arrangement turns that jet into a spread flow before it reaches anything expensive. It is one of the cheapest internals on the column and one of the most often left out of a revamp.

Types & Configurations

Impingement (splash) baffle

A plate set in front of a side inlet so the incoming jet hits it and spreads, instead of blasting directly into the bed or the vessel wall.

Feed pipe with distribution holes

A pipe inside the column with drilled openings that releases feed along its length, spreading it across the section rather than at one point.

Tangential inlet with baffle

Used where the feed has to be degassed or partly separated on entry. The baffle controls the swirl and protects the internals downstream.

Reflux / return and reboiler-return baffles

Protect the top bed from a high-velocity reflux return and the bottom of the column from vapour or two-phase reboiler return impingement.

Specifications

ParameterDetail
TypeImpingement baffle, perforated feed pipe, tangential inlet, return baffle
MaterialsSS304, SS316L, duplex, carbon steel, PP, PVDF, PTFE-lined
Design inputsNozzle size, feed rate and phase, column ID, distance to bed
OrientationMatched to existing nozzle; horizontal, vertical or tangential entry
FixingWelded brackets, bolted removable, or clamped to existing internals
Wear allowanceThicker section at the impingement point where the feed is abrasive or two-phase

Available Materials

SS304 · SS316L · Duplex stainless steel · Carbon steel · PP · PVDF · PTFE-lined steel

Typical Applications

  • Side feed nozzles on distillation columns
  • Reflux returns above the top bed
  • Reboiler returns and vapour inlets
  • Scrubber and quench inlets
  • Revamps where a new feed point has been added

Selection & Design Notes

  • Tell us the distance from the nozzle to the top of the bed. That distance decides whether a simple baffle is enough or whether a distributing pipe is needed.
  • Two-phase or flashing feed is the hard case — the jet expands as it enters, so the baffle has to be sized for the flashed velocity, not the line velocity.
  • Abrasive slurries and catalyst fines wear through a thin baffle quickly. Specify the service and we will increase section at the impingement zone.
  • Baffles are often omitted on revamps where a nozzle is reused for a higher rate. If the duty has changed, check the inlet device with it.
  • Keep the baffle removable if the column needs cleaning between runs; a welded-in plate is a permanent obstruction.

How the Options Compare

A plain impingement baffle is the cheapest protection and is adequate when the nozzle is well clear of the bed. A perforated feed pipe costs more but spreads liquid across the section, which is worth it when the feed rate is high or the bed is close. Tangential entries are chosen for phase separation reasons rather than distribution, and need a baffle to control the swirl they create.

Frequently Asked Questions

When is a feed baffle really necessary?

Whenever the inlet velocity is high enough to disturb the bed, when the nozzle is close to the packing, or when the feed is two-phase or flashing. Retrofits at higher rates are the classic case where the original device is no longer adequate.

How far below the nozzle should the baffle sit?

It depends on nozzle size and feed velocity — the aim is to let the jet spread before it reaches the bed. Send the nozzle size, feed rate and distance to the bed and we will size it.

Can you make a baffle to fit an existing nozzle?

Yes, that is most of what we do here. A nozzle detail drawing or measured dimensions are enough to fabricate a bolt-on or clamped baffle without vessel modification.

Does the baffle affect column performance?

It should not, if it is sized correctly. Its purpose is to stop the inlet from damaging distribution. An oversized or badly placed baffle can create its own maldistribution, which is why we design to the actual duty.

Other Tower Internals

Liquid Distributors

Factory-direct liquid distributors for packed columns: trough, orifice pan and spray types in SS304, SS316L, P…

Support Plates

Packing support plates and support grids for random and structured packing: bar grids, perforated plates and c…

Redistributors

Collector and chimney-tray liquid redistributors for tall packed beds. Re-mix liquid, correct wall flow and su…

Demister Supports

Support grids and hold-down bars for wire mesh and vane mist eliminators. Prevent pad sag and gas bypass, allo…

Talk to us about feed pipes & baffles

Tell us your flow rate, medium and operating conditions — we recommend the right packing and internals, and quote factory-direct.

Request a Quote WhatsApp