Liquid Redistributors for Deep Packed Beds

In a deep packed bed, liquid that starts out well distributed does not stay that way. It migrates toward the wall, and any small horizontal maldistribution at the top compounds with depth. Past a certain bed depth, efficiency stops improving with added packing unless the liquid is collected, mixed and spread again. That is what a redistributor does — and it is why tall columns are built as several beds rather than one.

Types & Configurations

Collector redistributor

Collects liquid across the full section, mixes it in a common sum, and re-distributes through orifices or troughs. The standard choice for multi-bed columns.

Chimney tray redistributor

A tray with vapour chimneys: gas rises through the chimneys while liquid is collected on the tray and re-spread. Allows a large open gas area and can double as a draw-off or feed point.

Wall wiper / peripheral baffle

A ring baffle that redirects liquid clinging to the column wall back into the bed. Cheap, simple, and often used together with a distributor rather than as a substitute for one.

Specifications

ParameterDetail
TypeCollector redistributor, chimney tray, wall wiper baffle
MaterialsSS304, SS316L, duplex, PP, PVDF, PTFE-lined steel
Design inputsColumn ID, liquid and vapour rates, bed depths, whether draw-off is required
Vapour pathChimneys or open area sized for your gas rate and allowable pressure drop
Combined functionsCan include side draw-off, feed introduction or temperature measurement point
AccessSegmented construction for manway installation; removable panels for cleaning

Available Materials

SS304 · SS316L · Duplex stainless steel · PP · PVDF · PTFE-lined steel

Typical Applications

  • Tall distillation columns built as multiple beds
  • Columns with side draws or intermediate feeds
  • Absorbers where wall flow has caused efficiency loss
  • Revamps where added bed depth gave no gain
  • Columns with varying liquid load along the height

Selection & Design Notes

  • If you have added packing to a column and seen no efficiency gain, maldistribution is a likely reason — a redistributor between beds is often the cheapest fix before considering new packing.
  • The bed depth at which redistribution becomes worthwhile depends on diameter, liquid load and how well the initial distribution was done. We will discuss it against your column rather than quote a fixed rule.
  • A redistributor costs pressure drop. If the column is close to its limits, the vapour path has to be sized carefully — this is where chimney trays earn their cost.
  • If a side draw or intermediate feed is planned, combine it with the redistributor instead of adding a separate tray. Fewer internals means less pressure drop and more usable space.
  • Specify whether the unit must be cleanable in place. Troughs and trays with removable panels are easier to wash than a fully welded assembly.

How the Options Compare

A collector redistributor gives the best re-mixing and is the standard multi-bed solution. A chimney tray costs more but handles high vapour rates with less pressure drop and can carry a draw-off. Wall wipers are a low-cost partial measure: they reduce wall flow but do not re-mix the bulk of the liquid, so they do not replace a proper redistributor in a tall bed.

Frequently Asked Questions

When does a column need a redistributor?

Broadly, when the bed is deep enough that maldistribution would compound before the liquid leaves the packing, and whenever a column is split into several beds. The exact depth depends on diameter and liquid load — send the column data and we will advise.

Does a redistributor reduce column capacity?

It occupies height and adds some pressure drop, which is why chimney designs exist for columns with little margin. The efficiency recovered from better distribution normally outweighs the loss.

Can it include a side draw-off?

Yes. Collector and chimney tray designs are routinely built with a draw-off sump and nozzle connection so one internal does two jobs.

Can you supply a redistributor for an existing column?

Yes. We need the internal diameter, support ring detail, nozzle positions and the bed arrangement. We then design to fit what is already in the vessel.

Other Tower Internals

Liquid Distributors

Factory-direct liquid distributors for packed columns: trough, orifice pan and spray types in SS304, SS316L, P…

Support Plates

Packing support plates and support grids for random and structured packing: bar grids, perforated plates and c…

Demister Supports

Support grids and hold-down bars for wire mesh and vane mist eliminators. Prevent pad sag and gas bypass, allo…

Feed Pipes & Baffles

Feed pipes, inlet distributors and impingement baffles that protect packed beds from high-velocity impingement…

Talk to us about redistributors

Tell us your flow rate, medium and operating conditions — we recommend the right packing and internals, and quote factory-direct.

Request a Quote WhatsApp